Rapid Set® Concrete Mix — FAQs
Very fast setting Concrete
What is Rapid Set® Concrete Mix?
Is this a modified portland cement product?
How soon can Rapid Set® be painted/coated/sealed?
Is a bonding agent necessary?
Can I blend other products with Rapid Set® Mortar Mix?
How thick can I apply this product?
Is Rapid Set® Concrete Mix air entrained?
How do I mix it?
How do I place and finish it?
How do I cure Rapid Set® Concrete Mix?
What are common applications for Rapid Set® Concrete Mix?
How do I increase the working time?
Can I use color?
How do I prepare the surface?
Where can I purchase Rapid Set®?
How much do I need?
Can I use it in wet applications?
What is the shelf life?
Does temperature affect Rapid Set® Concrete Mix?
____________________________________
A: Rapid Set® Concrete Mix is a blend of high-performance Rapid Set® Cement with quality rock and sand. It provides rapid strength gain, high durability and low shrinkage. Simply mix with water and it will reach STRUCTURAL STRENGTH IN 1 HOUR!
Q: Is this a modified portland cement product?
A: No. The high-performance properties come from the Rapid Set® Cement in the mix.
Q: How soon can Rapid Set® be painted, coated or sealed?
A: Rapid Set® reduces the waiting time prior to coating. Under dry conditions, water based coatings such as latex paint can be applied after the products is hardened and dry which usually takes 1 to 4 hours. Solvent based and impermeable coatings such as oil based paint and epoxy can be applied in 16 hours.
Experience has shown that some coatings can be applied in much less time. Follow the coating manufacturer 's recommendations for surface condition.
Q: Is a bonding agent necessary?
A: Bonding agents are not required. Proper surface preparation is the main component in achieving a good bond. If bonding agents are desired, they should be used as a supplement to good surface preparation, not as a substitute.
Q: Can I blend other bagged products with Rapid Set® Concrete Mix?
A: Blending with other products may give unpredictable results and is not recommended. The use of Rapid Set® approved additives and various colors are acceptable.
Q: How thick can I apply this product?
A: Any thickness greater than 2 inches.
Q: Is Rapid Set® Concrete Mix air entrained?
A: All Rapid Set® Concrete Mix is air entrained except for the product made in California.
Q: How do I mix it?
A: Just add water. The use of a mechanical mixer such as a mortar mixer or drill mounted mixer is recommended. To maximize working time, organize work so that all people and equipment are in place before mixing.
Q: How do I place and finish it?
A: Using traditional methods, place and strike-off to desired level. Rapid Set® is fast and does not bleed water so apply your final finish immediately after placing. Organize your tools and people so you can work quickly.
On flat work, fill to full depth and proceed horizontally. Do NOT place in layers.
Q: How do I cure Rapid Set® Concrete Mix?
A: Water cure all Rapid Set® Concrete Mix installations. The objective of water curing is to maintain a wet surface until the product has achieved sufficient strength. Begin curing as soon as the surface has lost it's moist sheen and continue for a minimum of 1 hour.
Q: What are common applications for Rapid Set® Concrete Mix?
A: Rapid Set® Concrete Mix can be used for most concrete applications. Common applications range from fence posts to airport runway repair. Formed work and general concrete repair are the most frequent use.
Q: How do I increase the working time?
A: You can increase the working time by lowering the mix temperature or using set retarding additives. Lower the mix temperature by keeping product cool and using chilled mix water. Set Control ® additive will increase working time and is available through our Concrete Pharmacy®.
Q: Can I use color?
A: Yes. The color of Rapid Set® Concrete Mix can be modified by using dry powder pigments designed for use in cement mixes.
Q: How do I prepare the surface?
A: Roughen the surface and remove all damaged or contaminated concrete. Make sure the repair surface is not contaminated by oil, paint, acids, dirt or other materials that will prevent a good bond. Immediately prior to placement, saturate the repair surface with water then remove any standing water.
Q: Where can I purchase Rapid Set®?
A: Rapid Set® products are available nationwide through contractor supply yards and home improvement centers.
Q: How much do I need?
A: One bag of Rapid Set® Concrete Mix yields 0.5 cubic feet. That's one square foot six inches deep. If you need an answer more specific to your application, contact us and we'll help you figure it out.
Q: Can I use it in wet applications?
A: Yes. Rapid Set® Concrete Mix is made with Rapid Set® Cement which is a hydraulic cement. A hydraulic cement hardens under water.
Q: What is the shelf life?
A: When stored in a dry location, in an undamaged package Rapid Set® Concrete Mix has a shelf life of 12 months.
Q: Does temperature affect Rapid Set® Concrete Mix?
A:Cold temperatures will slow the setting time of Rapid Set® Concrete Mix and warm temperatures will speed it up. Greater changes in temperature will have a more pronounced affect.